• 100% Black-owned, Level 1 B-BBEE

Pumps & Flow Management

Pumps & Flow Management

Service Overview

Moving slurry and bulk material through your plant efficiently and reliably. We supply slurry and process pumps, launders and distributors, conveyor belts and electrical motors matched to your duty requirements.

Our pumps are suited to abrasive materials and engineered for maximum flow efficiency and reduced wear, giving reliable performance in demanding conditions. Launders and slurry distributors are designed and supplied for controlled flow and even distribution across multiple processing lines, improving plant efficiency.

What we supply

  • Slurry and process pumps for abrasive duty
  • Launders and distributors designed to suit your plant
  • Conveyor belts resistant to wear, impact and corrosion
  • Electrical motors for pumps, conveyors and processing equipment
From flow to force, movement to protection, we deliver mining solutions that keep your operation running strong.
Pumps & Flow Management

Pumps for abrasive slurry, engineered for high efficiency and reduced wear.

Pumps & Flow Management

Even distribution across processing lines keeps your plant running at its best.

Designing flow as one system

Slurry leaves the mill, passes through pumps, pipes, distributors and launders, and reaches cyclones, spirals or flotation cells. Each part depends on the one before it. A pump selected for the wrong density, a distributor that splits unevenly or a launder laid too flat will each show up as lost recovery or high wear further down the line. This service treats pumps, flow distribution, belts and drives as parts of one material flow.

Products in this service

ProductTypical useKey specification (Songatech data)Product page
Horizontal slurry pumpsMill discharge, cyclone feed, tailings transfer5 to over 5 000 m³/h, heads up to 120 mSlurry pumps
Vertical sump and submersible pumpsSumps, pits, spillage and dewateringHigh chrome, rubber, PU or stainless wet endsSlurry pumps
Launders and distributorsSplitting feed to cyclones, spirals and cells50 to over 5 000 m³/h, ceramic, PU or rubber linedLaunders and distributors
Conveyor beltsOre transfer, stockpiles, overland conveyors400-2 400 mm wide, 200-3 150 N/mmConveyor belts
Electrical motorsPumps, conveyors, crushers, mills, fans0.75 kW to 5 MW, 380 V to 11 kV, IE2 to IE4Electrical motors

Pump selection steps

From tonnage to duty point

The duty point starts with the dry solids rate, the percent solids by mass and the solids SG. These give the slurry flow and the slurry SG. Static lift, pipe friction and fittings give the total head, which is then corrected for solids, because a slurry pump develops less head and efficiency on slurry than on water. The slurry pump sizing worked example takes one duty through each step to motor size.

Pipe velocity

Velocity in the pipeline must stay above the deposit velocity, or solids settle and friction climbs. It should not be much higher than needed, because wear in pipes and pump parts rises steeply with velocity. Long lines and lines with large static lift are checked against a system curve, as explained in the transfer pump and system curve article.

Wet end material

Rubber usually lasts longer on fine slurries with rounded particles. High chrome is chosen for coarse, sharp feed. Polyurethane and stainless suit specific fine or corrosive duties. The wet end materials guide compares them by duty.

Distributors and launders

A distributor feeding parallel cyclones or spiral banks must split solids as well as water evenly. Splitting by flow alone is not enough if coarse particles settle in one arm. Launders are sized on slope and velocity so that solids stay suspended; a launder that runs too flat sands up, and one that runs too steep wears its lining quickly. Lining choice follows the same logic as pumps: rubber for general abrasion, ceramic for severe sliding wear and polyurethane for sticky or corrosive slurry. Songatech builds lined launders and distributors to suit these conditions.

How the work is scoped and quoted

  • Dry tonnage, percent solids, solids SG, particle top size and d50.
  • Static lift, pipe length, diameter and the main fittings, or an isometric sketch.
  • Existing pump make and model, impeller and liner material, and wear life achieved.
  • For distributors: number of outlets, flow per outlet and the plant elevation available.
  • For motors: duty, power, voltage, mounting and the hazardous area classification if any.

The quote then names the pump, its operating speed, the wet end material and the motor, or the distributor and launder dimensions and lining.

Frequently Asked Questions

Built to last. Delivered on time. Local stock and fast lead times keep your plant running.

  • What information do I need for a slurry pump quote?
    Dry solids rate, percent solids by mass, solids SG, particle size, static lift, pipe length and diameter. If you are replacing a pump, add the make, model and current wear parts.
  • Why do slurry pumps wear out quickly?
    The common causes are a wet end material that does not suit the particle size, a pump running far from its best efficiency point, high speed and cavitation from a low sump level. Checking the operating point usually finds the cause.
  • Can you build distributors to fit an existing plant?
    Yes. Distributors and launders are custom fabricated to your drawing, flow rates, outlet count and tie-in points, with ceramic, polyurethane or rubber lining.
  • How do I request a quotation?
    Call 010 555 0828, email admin@songatech.co.za or use the quote form on our contact page. Send us your drawings or dimensions and we will match the product to your equipment.
  • Do you keep stock locally?
    Yes. Local stock at our Alrode head office and fast lead times mean consistent service and immediate distribution to mining operations.
  • Do you offer on-site support?
    Joint ventures and a strong regional presence let us offer tailored on-site support across South Africa's key mining regions and neighbouring countries.